Frequently Asked Questions IRONCLAD Fence Sensor

关于IRONCLAD栅栏式传感器的演示

Frequently Asked Questions About the IRONCLAD Fence Mounted Sensor

我在哪里可以买到IRONCLAD栅栏式传感器,如何选择合适的零件?

要下载代码表或其他材料,请参见我们的下载页面:


站点和系统设计手册

 

在哪里买?

电缆可以安装在滑门或平开门上吗?

Option 1 - Swing gate with NO conduit

Protection of an emergency gate or rarely used can be done by using the gate connector (sold separately), the connector will be connected to the cable at the opening point of the gate to allow the gate to be opened or closed. 不建议在经常使用的门上使用此连接。

门连接器图纸
Option 2 - Swing gate with WITH conduit

The protection of a single or double swing gate is done in the same method.
The sensor cable is looped on the gate then connected to a junction box RB-RBMCTXT and spliced with an RG6 direct burial to go under the gate, on the other end spliced back to a sensor cable and looped on the other side of the gate.
On the hinges, enough sensor needs to be left to allow it to freely move with opening and closing of the gate so the cable won’t stretch or bend sharply.

闸门保护图
Option 3 - Sliding gate with WITH conduit

Sliding gates can be treated in 2 ways

1. Bypass the gate and put a motion sensor across the gate to protect crossing.
2. Use RBtec sliding gate kit. Sliding gate is designed for light to medium traffic gates. Heavily used gates of hundreds of openings a day need to be protected with another technology such a camera or motion sensor.

展示滑门套件操作的视频

IRONCLAD套件包括什么?

The IRONCLAD Kit includes at least one spool/roll of sensor cable in the length of choice, End line termination unit (RB-RBMCTR) and RB-LPU304 (The analyzer/processor) in a weatherproof enclosure.

Power supply, Stainless steel ties, Weather station, Gate connector, Sliding Gate kit, and other accessories are optional and needed to be added separately.

Where to do I connect the IRONCLAD system?

Each analyzer/processor has 2 dry contact relay alarm outputs NO/NC, one per zone. Those outputs can be connected to ANY alarm system, CCTV system, access control, or any other system that can accept dry contact relay input such as sirens, strobe lights, and even fire alarms.

What length of fences can i protect with the IRONCLAD?

The IRONCLAD sensor cable is sold in spools/rolls of 250ft (75m), 500ft (150m) and 1000ft (300m).
Each processor can monitor up to 2 zones/spools which means the largest perimeter that can be covered with  套件为2000英尺(600m)。
In order to cover a larger perimeter multiple kits can be combined. Using multiple systems allows covering the whole fence line.
Shown below is a diagram of multiple 2 zone standalone kits combined to cover a larger perimeter.

4区布局

传感器的灵敏度可以调节吗?

Sure! The IRONCLAD system has 22 levels of sensitivity per zone that can be adjusted easily with dip switches. No need for tools, software, laptop or any knowledge.

我可以使用该系统吗?

No, the IRONCLAD system self-calibrates. The system is a plug and play system, it requires power, sensor inputs, and relay outputs and it works!

风或雨会引起误报吗?

The way the Ironclad system works: It detects only sharp frequency vibrations that are generated by cutting, climbing or jumping the fence. Vibrations caused by wind, rain and small animals are usually long-wave, low-frequency vibrations that would not be picked up by the system.

 

It’s the difference between tapping or climbing the fence which will get detected vs pushing on the fence like the wind that won’t.

 

最重要的是,我们有一个可选的气象站,它可以向分析仪提供有关其周围天气的实时信息,并能补偿风和雨,从而为过滤误报提供了更高的保证。

天气补偿装置是否会降低灵敏度以避免误报警?

没有,气象站将另一个变量添加到检测算法中,以帮助系统更好地忽略风噪声。它不会降低灵敏度以避免误报警。

电缆可以缩短/剪裁/拼接吗?

是! The cable can be cut to fit the fence size. Although the fence sensor cable is sold in fixed sizes it can be cut into any desired length. The cable is a 2 conductor copper wire.

我们是否需要改用另一根电缆绕过门?

If you would like to bypass the gate completely and not using RBtec gate connector then it’s recommended to use direct burial RG6 as a non-sensitive in the conduit.

如果电缆被切断,可以修理吗?

是! Repairing the cable is a 30 second process, RBtec offers a repair kit (RB-RBMCTXT) that bridges the cut in a weatherproof method to maintain the system performance.
修理箱安装在切割点处,传感器电缆连接到修理箱两侧的螺钉端子中,并且系统已备份并正在运行。

还有其他问题吗?请通过以下方式与我们联系 Info@rbtec.com

zh_CNChinese
en_USEnglish es_MXSpanish fr_CAFrench ru_RURussian pl_PLPolish he_ILHebrew tr_TRTurkish de_DEGerman ka_GEGeorgian it_ITItalian pt_BRPortuguese elGreek zh_CNChinese