MicAlert Microphonic Rigid Fence Sensor Cable

Protecting Rigid Steel Fences Made Easy, Reliable and Affordable.

• Ideal for installation on Welded Mesh, Metal Fences, Palisade and Ornamental, Wrought iron, and Aluminum fences.
• Plug and Play– Ready for installation of affordable kits.
• No Conduit – Attached directly to the fence without any conduit.
• No training or special tools are needed. Comes with an installation manual.
• No calibration – The system self-calibrates.
• Maintenance free – 2 years warranty on the sensor cable.
• 22 Levels of sensitivity per zone easily adjusted with dip switches.
• Dry contact relay outputs (NO or NC), can be connected to any alarm system/DVR.

Detect Intruders In Real Time At Your Fence Line with Fence Sensors

The MICALERT Microphonic fence sensor is a passive electronic intrusion detector system. The system is ideal for outdoor protection and can be easily installed on residential or high security Steel Fence, Palisade and Ornamental fences. The MICALERT microphonic fence-mounted sensor system is based on sensing types of frequencies associated with intrusion attempts while filtering ones related to weather conditions.

The MICALERT Microphonic Cable Fence Disturbance Sensor offers a solution for intrusion detection by analyzing typical noise patterns made by a forced entry attempt. The system can recognize motion caused by an attempt to pass through the fence and disregard signals caused by weather conditions, preventing nuisance alarms.
The sensor is designed to be installed directly on rigid fences without any conduit.
The Micalert has a UV-rated coating for outdoor installation and protection against all weather conditions.

The Micalert Palisade Steel Fence Sensor Is the ideal solution for protecting:

• Commercial and Industrial areas.
• Gated Communities
• Data Centers
• Water, Electrical and Utility substations.
• Car, RV, Boat or Equipment storage areas.
• Solar farms and Photovoltaic power plants.
• Self Storage facilities.
• Radio, Cellular, and Communication antennas.
• Any fenced location.

Sensor Layout of the Fence Alarm System Is:

1. Sensor Cable is pre-cut in 500ft/152m and 1000ft/305m

2. Each Processor (Analyzer) can monitor up to 2 zones (spools)

3. Maximum length per Processor is 2000ft/600m of sensor cable,
2 zones of 1000ft/305m

4. Each kit also includes: A processor in a weatherproof enclosure
and a sensor cable in chosen length.

5. To cover larger perimeters, there is an option to combine
as many kits as needed.

Operating Power Requirements:

• 12 – 48VDC 200mA @ 12VDC

Lightning Protection:

• 2 Layer Surge Protection
• Gas Discharge Devices on all Inputs/Outputs & Communication lines.

Alarm Inputs

• 4x Ironclad sensor cable inputs.
• 4x Intrusion and Line monitoring for accessories like magnets, contact, microwaves, and motion detectors.
• 1x Tamper switch.

Zone Status & Sensitivity Levels

• 8x Arm/Disarm via Jumper
• Twenty-two levels of sensitivity per zone on board.
• 500 Levels of sensitivity via software
• 1 Power Outage relay.

Alarm Outputs

• 8x Dry contact relays with contacts rated 1A @ 12VDC.
• 1x Tamper switch relay
• 1x Power Outage relay.

Connector:

• Sensor Input – 8x Screw terminal – Pair per zone.
• Alarm Output – 8x Screw terminal – Pair per zone

Cable:

• Outer Diameter: 3/32 Inch (3mm)
• Color: Black

Enclosure:

• NEMA 4X, IP-66
• 9.5 x 7.5 x 2.75” (24 x 19.5 x 7.0cm)
• Weight: 2.2 lbs. (1Kg)

Environment:

• Operating Temperature: – 40° to 221°F (-40° to 105°C)
• Relative Humidity up to 98% non-condensing.